bus-drivers-i2c-spi

用途

该技能用于指导智能体编写 Linux I2C 与 SPI 客户端驱动，涵盖总线注册、i2c_transfer / spi_sync、regmap 抽象、总线子节点的 DT compatible 匹配以及 probe 模式，与 skills/kernel/device-drivers 中的平台 MMIO 驱动形成互补。

适用场景

传感器或 PMIC 挂载在 I2C/SPI 总线上
将裸机 SPI 寄存器读取转换为内核驱动
使用 regmap 进行多字节寄存器访问
调试 -EREMOTEIO 或缺失 ACK

工作流程

1. I2C 客户端驱动

#include <linux/i2c.h>
#include <linux/mod_devicetable.h>

static int my_probe(struct i2c_client *client)
{
    struct regmap *map;

    map = devm_regmap_init_i2c(client, &my_regmap_config);
    if (IS_ERR(map))
        return PTR_ERR(map);

    dev_info(&client->dev, "probed at 0x%02x\n", client->addr);
    return 0;
}

static const struct of_device_id my_of_id[] = {
    { .compatible = "vendor,sensor" },
    { }
};
MODULE_DEVICE_TABLE(of, my_of_id);

static const struct i2c_device_id my_id[] = {
    { "mysensor", 0 },
    { }
};
MODULE_DEVICE_TABLE(i2c, my_id);

static struct i2c_driver my_driver = {
    .probe    = my_probe,
    .remove   = my_remove,
    .driver   = { .name = "mysensor", .of_match_table = my_of_id },
    .id_table = my_id,
};
module_i2c_driver(my_driver);

DT 子节点：

i2c1 {
    sensor@48 {
        compatible = "vendor,sensor";
        reg = <0x48>;
    };
};

2. 原始 I2C 传输

u8 reg = 0x0F, val;
struct i2c_msg msgs[] = {
    { .addr = client->addr, .flags = 0,       .len = 1, .buf = &reg },
    { .addr = client->addr, .flags = I2C_M_RD, .len = 1, .buf = &val },
};
ret = i2c_transfer(client->adapter, msgs, 2);

3. SPI 驱动

static int spi_probe(struct spi_device *spi)
{
    spi->mode = SPI_MODE_0;
    spi->bits_per_word = 8;
    spi_setup(spi);

    struct spi_transfer t = {
        .tx_buf = tx,
        .rx_buf = rx,
        .len    = len,
    };
    struct spi_message m;
    spi_message_init(&m);
    spi_message_add_tail(&t, &m);
    return spi_sync(spi, &m);
}

static struct spi_driver spi_drv = {
    .probe  = spi_probe,
    .driver = { .name = "my-spi", .of_match_table = my_of_match },
};
module_spi_driver(spi_drv);

4. regmap（寄存器映射首选）

static const struct regmap_config my_regmap_config = {
    .reg_bits   = 8,
    .val_bits   = 8,
    .max_register = 0x7F,
};

regmap_read(map, REG_STATUS, &val);
regmap_write(map, REG_CTRL, CTRL_ENABLE);
regmap_update_bits(map, REG_CTRL, MASK, ENABLE);

5. 调试

i2cdetect -y 1
i2cdump -y 1 0x48
cat /sys/bus/i2c/devices/i2c-1/1-0048/name

6. 智能体用法

/bus-drivers-i2c-spi Write regmap-based driver for I2C PMIC at 0x58

常见问题

症状	原因	修复
-EREMOTEIO	NACK — 地址错误	i2cdetect；检查 DT 中的 reg
SPI 模式错误	CPOL/CPHA 不匹配	匹配数据手册 + spi->mode
Probe defer	稳压器/时钟供应方	返回 -EPROBE_DEFER
regmap -EIO	16 位 vs 8 位寄存器	设置 reg_bits、val_bits
未使用 DMA	小 spi_sync 可以	批量传输用 spi_sync_transfer

技能介绍

用途

适用场景

工作流程

1. I2C 客户端驱动

2. 原始 I2C 传输

3. SPI 驱动

4. regmap（寄存器映射首选）

5. 调试

6. 智能体用法

常见问题

相关技能