esp32-rust-embedded

ESP32 Embedded Rust Specialist

Expert guidance for no-std Rust development on ESP32 microcontrollers using the ESP-RS ecosystem and Embassy async framework.

ESP-RS Ecosystem Stack

Core Dependencies

esp-hal = { version = "~1.1.0", features = ["esp32s3", "log-04", "unstable"] }
esp-rtos = { version = "0.3.0", features = ["embassy", "esp-alloc", "esp-radio", "esp32s3", "log-04"] }
esp-radio = { version = "0.18.0", features = ["esp-alloc", "esp32s3", "log-04", "unstable", "wifi"] }
esp-bootloader-esp-idf = { version = "0.5.0", features = ["esp32s3", "log-04"] }
esp-alloc = "0.10.0"
esp-println = { version = "0.17.0", features = ["esp32s3", "log-04"] }

smoltcp is now a DIRECT dependency (no longer a feature of esp-radio)

smoltcp = { version = "0.13.0", default-features = false, features = [ "log", "medium-ethernet", "multicast", "proto-dhcpv4", "proto-dns", "proto-ipv4", "socket-dns", "socket-icmp", "socket-raw", "socket-tcp", "socket-udp", ] }

### Embassy Framework
```toml
embassy-executor = { version = "0.10.0", features = ["log"] }
embassy-time = { version = "0.5.0", features = ["log"] }
embassy-net = { version = "0.9.1", features = ["dhcpv4", "log", "medium-ethernet", "tcp", "udp"] }
embassy-sync = { version = "0.7.2" }

Dependency Hierarchy

esp-radio (WiFi) -> esp-rtos (scheduler) -> esp-hal (HAL) -> esp-phy (PHY)
embassy-executor -> embassy-time -> embassy-sync -> embassy-net

Rust Edition & MSRV

• Edition: 2024 (edition = "2024" in Cargo.toml)
• MSRV: 1.88 (rust-version = "1.88")
• Binary location: src/bin/main.rs (not src/main.rs) — [[bin]] entry required in Cargo.toml

Build & Flash

Environment Setup

# Install ESP toolchain (one-time)
espup install
source $HOME/export-esp.sh

# Configure credentials (.env file)
cp .env.dist .env
# Edit: WIFI_SSID, WIFI_PSK, MQTT_HOSTNAME, MQTT_USERNAME, MQTT_PASSWORD

Build Commands

# Quick build and flash
./run.sh

# Manual release build (recommended)
cargo run --release

# Debug build (slower on device)
cargo run

Cargo Profile Optimization

[profile.dev]
opt-level = "s"  # Rust debug too slow for ESP32

[profile.release]
lto = 'fat'
opt-level = 's'
codegen-units = 1

Common Build Errors

Linker error: undefined symbol _stack_start

• Check build.rs has linkall.x configuration
• Verify esp-hal version compatibility

undefined symbol: esp_rtos_* ("esp-radio has no scheduler enabled")

• Ensure esp-rtos is started with BOTH a timer AND a software interrupt (changed in 0.3.0):

let timg0 = TimerGroup::new(peripherals.TIMG0);
let sw_interrupt = esp_hal::interrupt::software::SoftwareInterruptControl::new(
    peripherals.SW_INTERRUPT
);
esp_rtos::start(timg0.timer0, sw_interrupt.software_interrupt0);

Environment variable errors

• Variables are compile-time via env!() macro
• Changes require full rebuild

No-Std Patterns

Application Entry

#![no_std]
#![no_main]
// Recommended lints (now standard in esp-generate templates)
#![deny(clippy::mem_forget)]  // esp-hal types must not be mem::forgotten
#![deny(clippy::large_stack_frames)]

use embassy_executor::Spawner;
use esp_hal::{clock::CpuClock, timer::timg::TimerGroup};

esp_bootloader_esp_idf::esp_app_desc!();

#[esp_rtos::main]
async fn main(spawner: Spawner) -> ! {
    // Initialize logger (reads RUST_LOG env var at compile time via esp-config)
    esp_println::logger::init_logger_from_env();

    // Initialize HAL with max CPU clock
    let config = esp_hal::Config::default().with_cpu_clock(CpuClock::max());
    let peripherals = esp_hal::init(config);

    // Setup heap allocator using reclaimed memory (replaces dram2_uninit approach)
    esp_alloc::heap_allocator!(#[esp_hal::ram(reclaimed)] size: 73744);

    // Start RTOS scheduler — now requires BOTH a timer AND a software interrupt
    let timg0 = TimerGroup::new(peripherals.TIMG0);
    let sw_interrupt = esp_hal::interrupt::software::SoftwareInterruptControl::new(
        peripherals.SW_INTERRUPT
    );
    esp_rtos::start(timg0.timer0, sw_interrupt.software_interrupt0);

    // Spawn tasks...
    let _ = spawner;
    loop {}
}

Memory Management

• Use esp-alloc for dynamic allocation
• Prefer heapless collections with compile-time capacity
• Use static_cell::StaticCell for 'static lifetime requirements

String Handling

use alloc::string::String;      // Dynamic strings (heap)
use heapless::String;           // Bounded strings (stack)

let s: heapless::String<64> = heapless::String::new();

Avoid cloning when possible.

StaticCell Pattern

static CHANNEL: StaticCell<Channel<NoopRawMutex, Data, 3>> = StaticCell::new();

// In async function
let channel: &'static mut _ = CHANNEL.init(Channel::new());
let (sender, receiver) = (channel.sender(), channel.receiver());

Hardware Patterns

GPIO Configuration

use esp_hal::gpio::{Level, Output, OutputConfig, Pull, DriveMode};

// Standard output
let pin = Output::new(peripherals.GPIO2, Level::Low, OutputConfig::default());

// Open-drain for sensors like DHT11
let pin = Output::new(
    peripherals.GPIO1,
    Level::High,
    OutputConfig::default()
        .with_drive_mode(DriveMode::OpenDrain)
        .with_pull(Pull::None),
).into_flex();

ADC Reading with Calibration

use esp_hal::analog::adc::{Adc, AdcConfig, AdcCalCurve, Attenuation};

let mut adc_config = AdcConfig::new();
let pin = adc_config.enable_pin_with_cal::<_, AdcCalCurve<ADC2>>(
    peripherals.GPIO11,
    Attenuation::_11dB  // 0-3.3V range
);
let adc = Adc::new(peripherals.ADC2, adc_config);

// Read with nb::block!
let value = nb::block!(adc.read_oneshot(&mut pin))?;

Peripheral Bundles Pattern

pub struct SensorPeripherals {
    pub dht11_pin: GPIO1<'static>,
    pub moisture_pin: GPIO11<'static>,
    pub power_pin: GPIO16<'static>,
    pub adc2: ADC2<'static>,
}

Async Task Architecture

Task Definition

#[embassy_executor::task]
pub async fn my_task(sender: Sender<'static, NoopRawMutex, Data, 3>) {
    loop {
        // Do work
        sender.send(data).await;
        Timer::after(Duration::from_secs(5)).await;
    }
}

Task Spawning

spawner.spawn(sensor_task(sender, peripherals)).ok();
spawner.spawn(update_task(stack, display, receiver)).ok();

Inter-Task Communication

Channel (multiple values)

use embassy_sync::{blocking_mutex::raw::NoopRawMutex, channel::Channel};

static CHANNEL: StaticCell<Channel<NoopRawMutex, Data, 3>> = StaticCell::new();
// sender.send(data).await / receiver.receive().await

Signal (single notification)

use embassy_sync::{blocking_mutex::raw::CriticalSectionRawMutex, signal::Signal};

static SIGNAL: Signal<CriticalSectionRawMutex, ()> = Signal::new();
// SIGNAL.signal(()) / SIGNAL.wait().await

Reconnection Loop Pattern

'reconnect: loop {
    let mut client = initialize_client().await?;
    loop {
        match client.process().await {
            Ok(_) => { /* handle messages */ }
            Err(e) => {
                println!("Error: {:?}", e);
                continue 'reconnect;  // Reconnect on error
            }
        }
    }
}

Power Management

Deep Sleep Configuration

use esp_hal::rtc_cntl::{Rtc, sleep::{RtcSleepConfig, TimerWakeupSource, RtcioWakeupSource, WakeupLevel}};

pub fn enter_deep(wakeup_pin: &mut dyn RtcPin, rtc_cntl: LPWR, duration: Duration) -> ! {
    // GPIO wake source
    let wakeup_pins: &mut [(&mut dyn RtcPin, WakeupLevel)] = &mut [(wakeup_pin, WakeupLevel::Low)];
    let ext0 = RtcioWakeupSource::new(wakeup_pins);

    // Timer wake source
    let timer = TimerWakeupSource::new(duration.into());

    let mut rtc = Rtc::new(rtc_cntl);
    let mut config = RtcSleepConfig::deep();
    config.set_rtc_fastmem_pd_en(false);  // Keep RTC fast memory powered

    rtc.sleep(&config, &[&ext0, &timer]);
    unreachable!();
}

RTC Fast Memory Persistence

use esp_hal::ram;

#[ram(unstable(rtc_fast))]
pub static BOOT_COUNT: RtcCell<u32> = RtcCell::new(0);

// Survives deep sleep - read/write with .get()/.set()
let count = BOOT_COUNT.get();
BOOT_COUNT.set(count + 1);

Power Optimization

• Toggle sensor power pins only during reads
• Use power save mode on displays
• Gracefully disconnect WiFi before sleep
• Keep awake duration minimal

WiFi Networking

Connection Setup

// esp_radio::init() is GONE — wifi::new() is called directly (as of esp-radio 0.18+)
use esp_radio::wifi::{self, ClientConfig, ModeConfig, WifiController};

let (mut controller, interfaces) =
    esp_radio::wifi::new(peripherals.WIFI, Default::default())
        .expect("Failed to initialize Wi-Fi controller");

let client_config = ModeConfig::Client(
    ClientConfig::default()
        .with_ssid(env!("WIFI_SSID").try_into().unwrap())
        .with_password(env!("WIFI_PSK").try_into().unwrap()),
);

controller.set_config(&client_config)?;
controller.start_async().await?;
controller.connect_async().await?;

Embassy-Net Stack

use embassy_net::{Config, Stack, StackResources};

let config = Config::dhcpv4(DhcpConfig::default());
let (stack, runner) = embassy_net::new(wifi_interface, config, stack_resources, seed);

// Wait for link and IP
loop {
    if stack.is_link_up() { break; }
    Timer::after(Duration::from_millis(500)).await;
}

loop {
    if let Some(config) = stack.config_v4() {
        println!("IP: {}", config.address);
        break;
    }
    Timer::after(Duration::from_millis(500)).await;
}

Graceful WiFi Shutdown

pub static WIFI_SIGNAL: Signal<CriticalSectionRawMutex, ()> = Signal::new();

// In connection task
WIFI_SIGNAL.wait().await;
controller.stop_async().await?;

// Before deep sleep
WIFI_SIGNAL.signal(());

Sensor Patterns

ADC Sampling with Warmup

async fn sample_adc_with_warmup<PIN, ADC>(
    adc: &mut Adc<ADC, Blocking>,
    pin: &mut AdcPin<PIN, ADC>,
    warmup_ms: u64,
) -> Option<u16> {
    Timer::after(Duration::from_millis(warmup_ms)).await;
    nb::block!(adc.read_oneshot(pin)).ok()
}

Power-Controlled Sensor Read

async fn read_sensor(adc: &mut Adc, pin: &mut AdcPin, power: &mut Output) -> Option<u16> {
    power.set_high();
    let result = sample_adc_with_warmup(adc, pin, 50).await;
    power.set_low();
    result
}

Outlier-Resistant Averaging

fn calculate_average<T: Copy + Ord + Into<u32>>(samples: &mut [T]) -> Option<T> {
    if samples.len() <= 2 { return None; }

    samples.sort_unstable();
    let trimmed = &samples[1..samples.len() - 1];  // Remove min/max

    let sum: u32 = trimmed.iter().map(|&x| x.into()).sum();
    (sum / trimmed.len() as u32).try_into().ok()
}

Display Integration

ST7789 Parallel Interface

use mipidsi::{Builder, options::ColorInversion};

let di = display_interface_parallel_gpio::Generic8BitBus::new(/*pins*/);
let mut display = Builder::new(ST7789, di)
    .display_size(320, 170)
    .invert_colors(ColorInversion::Inverted)
    .init(&mut delay)?;

Power Save Mode

display.set_display_on(false)?;  // Enter power save
// Before deep sleep
power_pin.set_low();

Error Handling

Module Error Pattern

#[derive(Debug)]
pub enum Error {
    Wifi(WifiError),
    Display(display::Error),
    Mqtt(MqttError),
}

impl From<WifiError> for Error {
    fn from(e: WifiError) -> Self { Self::Wifi(e) }
}

Fallible Main Pattern

// Note: #[esp_rtos::main] (not use esp_rtos::main; #[main])
// Note: main now returns `-> !` (diverging)
#[esp_rtos::main]
async fn main(spawner: Spawner) -> ! {
    if let Err(error) = main_fallible(spawner).await {
        log::error!("Fatal: {:?}", error);
        esp_hal::system::software_reset();
    }
    unreachable!()
}

async fn main_fallible(spawner: Spawner) -> Result<(), Error> {
    // Application logic with ? operator
}

Dependency Updates

Safe Update Process

cargo outdated
cargo update -p esp-hal
cargo build --release
cargo clippy -- -D warnings

Breaking Change Patterns

• GPIO API changes frequently (OutputConfig)
• Timer initialization changes
• Feature flag renames
• esp-rtos 0.3.0: esp_rtos::start() now requires 2 args (timer + software interrupt)
• esp-radio 0.18.0: esp_radio::init() removed; call esp_radio::wifi::new() directly
• smoltcp: now a direct dependency, not a feature of esp-radio
• heap_allocator!: use #[esp_hal::ram(reclaimed)] instead of #[unsafe(link_section = ".dram2_uninit")]
• Always check esp-hal release notes and migrate with esp-generate's generated templates as reference

Version Alignment

Update Embassy crates together:

cargo update -p embassy-executor -p embassy-time -p embassy-sync -p embassy-net

esp-generate (project scaffold tool)

# Install
cargo install esp-generate --locked

# Generate ESP32-S3 project with Embassy + WiFi + alloc
esp-generate --chip esp32s3 -o unstable-hal -o embassy -o alloc -o wifi -o log my-project

# Available options: unstable-hal, alloc, wifi, ble-trouble, embassy,
#   probe-rs, defmt, log, esp-backtrace, embedded-test, wokwi, ci,
#   vscode, neovim, helix, zed

Note: wifi option now requires both unstable-hal and alloc.
Note: embassy option requires unstable-hal.

Debugging

Serial Logging

use esp_println::println;
// New: reads RUST_LOG at compile time via esp-config (.cargo/esp-config.toml)
esp_println::logger::init_logger_from_env();
// Or explicitly set a level:
// esp_println::logger::init_logger(log::LevelFilter::Info);
log::info!("Debug: value = {}", value);
println!("Debug: value = {}", value); // also works

Common Runtime Issues

• WiFi fails: Check 2.4GHz network, signal strength
• MQTT fails: Verify DNS resolution, broker credentials
• Sensors fail: Check warmup delays, power pin toggling
• Display blank: Ensure GPIO15 is HIGH (power enable)
• Sleep wake fails: Verify RTC fast memory config

Software Reset

use esp_hal::system::software_reset;
software_reset();  // Clean restart on unrecoverable error