matlab-model-robot-kinematics

Robot Modeling & Kinematics

Build manipulator models correctly and validate every kinematic solution.

When to Use

• Any task that requires a robot model in MATLAB (even if the goal is downstream: animation, pick-and-place, trajectory, motion planning)
• User mentions a specific manipulator by name (UR5e, KUKA iiwa14, Panda, Kinova Gen3, etc.)
• Loading, building, or importing a robot model
• Simulating, animating, or visualizing a manipulator
• Tasks involving lifting, reaching, picking, placing, or grasping
• Adding visual meshes or collision geometry
• Attaching a gripper to a manipulator
• Choosing between inverseKinematics vs generalizedInverseKinematics
• Validating IK/GIK solutions (exit flags, position error, joint continuity)

When NOT to Use

• Collision-free motion planning (RRT, CHOMP, path planning) — use a motion planning skill
• Trajectory generation (contopptraj, cubicpolytraj, trapveltraj) — use a trajectory skill
• Closed-loop parallel mechanisms (delta, Stewart) — see references/parallel-robot-guidance.md
• Mobile robot navigation or wheeled platforms — not covered here
• Dynamics simulation (inverseDynamics, forwardDynamics) — separate domain

Workflow

Step 1: Determine Model Source

Choose the highest-fidelity source available:

Priority	Source	When to Use	Why
1	loadrobot	Robot exists in the library	Includes collision meshes, inertias, visuals
2	importrobot	User has URDF/Xacro/SDF file	Preserves mesh references
3	Build from DH	Only DH parameters available	No collision meshes unless added manually

Critical: A robot without collision meshes will cause downstream motion planning to silently report "collision-free" paths that actually collide. Always prefer sources that include meshes.

If the user says "build a robot" but names a known robot (UR5e, KUKA iiwa, Panda, etc.), suggest loadrobot first.

After importing from URDF, Simscape, or CAD: Check if collision meshes are present. Simscape Multibody models and many URDFs/CAD exports only provide visual geometry — no collision meshes. If collision meshes are missing, read references/import-mesh-handling.md for the decision tree on generating them from visuals.

Step 2: Load or Build the Model

Always set DataFormat="row" — this is required for planning and dynamics workflows.

Option A — loadrobot:

robot = loadrobot("universalUR5e", DataFormat="row");

Option B — importrobot (URDF/Xacro/SDF):

robot = importrobot("myRobot.urdf", DataFormat="row");

If the URDF has only visual geometry (no <collision> tags), add VHACD collision decomposition at import time:

opts = vhacdOptions("RigidBodyTree");
opts.SourceMesh = "VisualGeometry";
robot = importrobot("myRobot.urdf", DataFormat="row", ...
    MeshPath="path/to/meshes", CollisionDecomposition=opts);

Option C — Build from DH parameters:

robot = rigidBodyTree(DataFormat="row");

body = rigidBody("link1");
jnt = rigidBodyJoint("joint1", "revolute");
setFixedTransform(jnt, [a alpha d 0], "dh");
jnt.PositionLimits = [-pi, pi];
body.Joint = jnt;

addVisual(body, "Cylinder", [0.04, 0.3]);
addCollision(body, "Cylinder", [0.05, 0.3]);

addBody(robot, body, "base");

Step 3: Ensure tool0 Exists with Z = Outward

Before attaching a gripper, the robot MUST have a tool0 body whose local Z-axis points along the arm's outward direction (away from the wrist). Most loadrobot models satisfy this already — but KUKA iiwa models do not.

Check references/ee-frame-alignment.md for the full compatibility table and diagnostic procedure.

If the robot already has tool0 with Z = outward (all UR, ABB, Techman, FANUC, Kinova, Yaskawa): proceed directly to gripper attachment.

If the robot lacks tool0 or EE Z is misaligned (KUKA iiwa 7/14): add a corrective tool0 frame:

% KUKA iiwa: iiwa_link_ee Z is perpendicular to arm — fix with Ry(90°)
tool0 = rigidBody("tool0");
tool0Joint = rigidBodyJoint("tool0_joint", "fixed");
R_correction = [0 0 1; 0 1 0; -1 0 0]; % Ry(90°)
setFixedTransform(tool0Joint, rotm2tform(R_correction));
tool0.Joint = tool0Joint;
addBody(robot, tool0, "iiwa_link_ee");

For unknown robots (URDF imports): Run the diagnostic check from references/ee-frame-alignment.md to verify alignment before attaching anything.

Step 4: Configure the Model

Visuals vs collisions — both are needed, for different purposes:

Function	Purpose	Used By
addVisual(body, shape, dims)	Display appearance	show for visualization
addCollision(body, shape, dims)	Planning geometry	checkCollision, motion planners

To color a visual: addVisual(body, "Mesh", stlFile, tform, FaceColor=[1 0.8 0])

Robots from loadrobot already have both. When building from scratch, add both explicitly.

Attach a gripper (MANDATORY for manipulation tasks):

If the task involves object interaction (picking, placing, lifting, grasping, manipulating), a gripper is required — do not skip this step. Only omit for pure visualization or reachability studies with no object contact.

Before building ANY custom gripper, you MUST read references/gripper-models.md. Available models include both parallel-jaw (robotiq2F85, 85mm opening) AND vacuum grippers (robotiqEPick variants for large/flat objects). Do NOT assume robotiq2F85 is the only option.

1. Read references/gripper-models.md
2. Follow the decision tree in that file (check compatibility → check object size → select grip strategy)
3. Only build custom if no provided model fits (incompatible manipulator AND object unsuitable for vacuum)

gripper = loadrobot("robotiq2F85", DataFormat="row");
addSubtree(robot, "tool0", gripper, ReplaceBase=false);

Critical: Always use ReplaceBase=false. The default (true) merges the gripper's base link into the parent body, silently discarding the base visual mesh (the gripper housing/coupling). All provided grippers have a base visual that is lost without this flag.

After attaching a gripper, add a contact frame at the gripper's contact point (fixed joint, zero DOF added), then solve IK to that frame. This avoids confusing tip frame orientations and manual offset math. See references/gripper-models.md for per-gripper offsets and the full pattern.

contactFrame = rigidBody("contact_point");
contactJoint = rigidBodyJoint("contact_joint", "fixed");
setFixedTransform(contactJoint, trvec2tform([0, 0, gripperOffset]));
contactFrame.Joint = contactJoint;
addBody(robot, contactFrame, "tool0");

Add a custom end-effector frame (when no gripper is attached or you need a specific offset):

ee = rigidBody("tool_tip");
eeJoint = rigidBodyJoint("tool_tip_joint", "fixed");
setFixedTransform(eeJoint, trvec2tform([0.1, 0, 0]));
ee.Joint = eeJoint;
addBody(robot, ee, "tool0");

Step 5: Verify the Model with Kinematics

Use FK and IK to confirm the model is built correctly — correct link lengths, joint axes, limits, and end-effector frame placement.

Verify with FK: Move to a known configuration and check the end-effector reaches the expected position.

q = homeConfiguration(robot);
tform = getTransform(robot, q, "tool0");
fprintf("Home position: [%.3f, %.3f, %.3f] m\n", tform(1:3,4));

Visually confirm the pose makes sense:

figure;
show(robot, q, Frames="off");
axis auto;
title("Home configuration");

Verify with IK: Pick a target you know is reachable and confirm the solver converges.

Decision — IK vs GIK:

Use	When
inverseKinematics	Single target pose, no extra constraints
generalizedInverseKinematics	Multiple constraints (position + aiming, joint bounds, orientation, etc.)

See references/gik-constraints.md for all available GIK constraint types.

ik = inverseKinematics(RigidBodyTree=robot);
weights = [0.25 0.25 0.25 1 1 1];
targetPose = trvec2tform([0.4, 0.1, 0.3]) * eul2tform([0 pi 0], "ZYX");
[qSol, solnInfo] = ik("tool0", targetPose, weights, homeConfiguration(robot));

Step 6: Validate Every IK/GIK Solution (MANDATORY)

Never skip this step. Agents consistently skip validation and deliver solutions that silently failed.

After inverseKinematics:

if solnInfo.ExitFlag <= 0
    warning("IK did not converge. ExitFlag: %d, Status: %s", ...
        solnInfo.ExitFlag, solnInfo.Status);
end

tformActual = getTransform(robot, qSol, "tool0");
posError = norm(tformActual(1:3,4)' - targetPose(1:3,4)');
if posError > 1e-3
    warning("IK position error %.4f m exceeds threshold.", posError);
end

After generalizedInverseKinematics:

if solInfo.ExitFlag <= 0
    warning("GIK did not converge. ExitFlag: %d, Status: %s", ...
        solInfo.ExitFlag, solInfo.Status);
end

for i = 1:numel(solInfo.ConstraintViolations)
    cv = solInfo.ConstraintViolations(i);
    if cv.Violation > 1e-3
        warning("Constraint %d (%s) violated: %.4f", i, cv.Type, cv.Violation);
    end
end

For sequential waypoints — check joint continuity:

for i = 2:size(qAll, 1)
    maxJump = max(abs(qAll(i,:) - qAll(i-1,:)));
    if maxJump > deg2rad(30)
        warning("Joint jump of %.1f deg between waypoints %d and %d.", ...
            rad2deg(maxJump), i-1, i);
    end
end

Key Functions

Function	Purpose	Toolbox	Available From
loadrobot	Load built-in robot with meshes	Robotics System Toolbox	R2019b
importrobot	Import from URDF/Xacro/SDF/Simscape	Robotics System Toolbox	R2017a
rigidBodyTree	Create empty robot model	Robotics System Toolbox	R2016b
setFixedTransform	Set joint transform (DH or homogeneous)	Robotics System Toolbox	R2016b
addVisual	Add visual geometry for display	Robotics System Toolbox	R2019a
addCollision	Add collision geometry for planning	Robotics System Toolbox	R2019b
addSubtree	Attach subtree (gripper) to body	Robotics System Toolbox	R2016b
getTransform	Compute FK for a configuration	Robotics System Toolbox	R2016b
inverseKinematics	Solve IK for single target pose	Robotics System Toolbox	R2016b
generalizedInverseKinematics	Solve IK with multiple constraints	Robotics System Toolbox	R2017a
show	Visualize robot configuration	Robotics System Toolbox	R2016b

Patterns

Visualization

figure;
show(robot, q, Frames="off");
axis auto;
view(45, 30);
title("Robot at configuration q");

For multiple configurations, use tiledlayout/nexttile:

figure;
tiledlayout(1, 3);
for i = 1:3
    nexttile;
    show(robot, qAll(i,:), Frames="off", PreservePlot=false);
    axis auto;
    title(sprintf("Waypoint %d", i));
end

Using Initial Guess to Improve IK Convergence

When solving IK for sequential waypoints, use the previous solution as the initial guess:

qPrev = homeConfiguration(robot);
for i = 1:numWaypoints
    [qSol, solnInfo] = ik("tool0", targetPoses(:,:,i), weights, qPrev);
    % ... validate ...
    qPrev = qSol;
end

Conventions

• Always set DataFormat="row" on creation or import
• Joint limits in radians (use deg2rad when specifying in degrees)
• Use Frames="off" and axis auto for clean visualization
• Use tiledlayout/nexttile instead of subplot
• Name end-effector frames descriptively (e.g., "tool_tip", "bucket_tip")
• Weights for inverseKinematics: [orientation(3) position(3)] — set position weights higher for position-priority tasks

Common Mistakes

Mistake	Why It's Wrong	Correct Approach
Building from DH when loadrobot has the robot	No collision meshes → planning silently fails	Check loadrobot library first
Using addCollision for visual appearance	Collision geometry is simplified, not rendered by show	Use addVisual for display, addCollision for planning
Skipping IK validation	Solution may not converge; ExitFlag <= 0 means failure	Always check ExitFlag and verify position error via FK
Using DataFormat="column" or "struct"	Incompatible with planning/trajectory functions that expect row vectors	Always use DataFormat="row"
Skipping gripper for manipulation tasks	Object interaction (pick, lift, grasp) requires a gripper on the model	Always attach a gripper when the task involves object contact
Solving IK to "tool0" or tip body without a contact frame	"tool0" is the flange (offset from contact point); tip body frames have confusing 90° rotations	Add a fixed "contact_point" frame at the gripper offset, solve IK to that
Building a custom gripper from scratch	Provided models have accurate geometry and are ready to attach	Check references/gripper-models.md for available grippers
Using robotiq2F85 for objects > 85 mm	Jaw cannot open wide enough to grasp the object	Compare object dimensions to gripper max opening; use vacuum for large objects
Using IK when multiple constraints are needed	inverseKinematics only handles a single pose target	Use generalizedInverseKinematics with constraint objects
Not checking joint continuity for waypoint sequences	Large jumps between solutions cause unsafe trajectories	Compare consecutive solutions, flag jumps > 30 deg
Using addSubtree without ReplaceBase=false	Gripper base visual mesh is silently discarded; housing disappears from visualization	Always pass ReplaceBase=false when attaching grippers
Attaching gripper to KUKA iiwa without frame correction	iiwa_link_ee Z is perpendicular to arm; gripper points sideways	Add tool0 with Ry(90°) correction before attaching — see references/ee-frame-alignment.md
Assuming all loadrobot models have tool0 with Z = outward	Some robots (KUKA iiwa) lack tool0 or have misaligned EE frames	Check references/ee-frame-alignment.md table or run diagnostic before gripper attachment
Using rigidBodyTree for closed-loop parallel robots	Cannot represent closed kinematic chains	See references/parallel-robot-guidance.md

---

Copyright 2026 The MathWorks, Inc.

---