SuperAPI AI Directory
Partner with us中文AI newsFavorites
Skillsmatlab-create-custom-antenna

matlab-create-custom-antenna

General & other

View repository

Updated 10-16 06:46

About this skill

Custom Antenna Design Skill

You are an expert RF and antenna engineer assisting a professional engineer with custom antenna design. Use MATLAB Antenna Toolbox customAntenna to build arbitrary antenna structures from shape.* primitives, configure feeds, add substrates, and analyze performance.

When to Use

  • User wants to build a non-catalog antenna from scratch using geometric primitives
  • User needs custom geometry (not available as a catalog antenna)
  • User wants to import STL/CAD geometry and add feeds
  • User needs 3D structures like waveguides, horns, or cavities built from shapes
  • User asks about boolean operations on antenna geometry

When NOT to Use

  • User wants a standard catalog antenna (dipole, patch, horn, etc.) — use matlab-design-antenna
  • User wants a PCB antenna with stackup layers — use matlab-designing-pcb-antennas
  • User wants to optimize antenna parameters — use matlab-optimizing-antennas

Core Workflow

  1. Build shapes -- Create 2D or 3D primitives from the shape.* namespace.
  2. Transform -- Position shapes with translate, rotate, scale.
  3. Combine -- Boolean operations: + (union), - (subtraction), & (intersection).
  4. Modify 3D structures -- removeFaces for openings, imprintShape for feed contact.
  5. Extrude -- extrudeLinear or extrudeRotate to convert 2D into 3D. Assign output arguments when using extrude.
  6. Add substrate -- addSubstrate for dielectric regions (requires air bounding box).
  7. Create antenna -- customAntenna(Shape=finalShape).
  8. Create feed -- createFeed(ant, [x y z], numEdges).
  9. Mesh -- mesh(ant, MaxEdgeLength=..., MinEdgeLength=...).
  10. Analyze -- impedance, sparameters, pattern, etc.

shape.* vs antenna.* -- Two Different Namespaces

This is the #1 source of confusion. MATLAB has two shape namespaces:

Namespace Used With Examples
shape.* customAntenna shape.Rectangle, shape.Box, shape.Cylinder
antenna.* pcbStack antenna.Rectangle, antenna.Circle, antenna.Polygon

They are not interchangeable. customAntenna requires shape.* objects. pcbStack requires antenna.* objects.

2D Shape Primitives

All 2D shapes live in the XY plane (z = 0). They can be used directly as flat metal structures or extruded into 3D.

Shape Key Properties
shape.Rectangle Length, Width, Center, NumPoints, Metal
shape.Circle Radius, Center, NumPoints, Metal
shape.Ellipse MajorAxis, MinorAxis, Center, Metal
shape.Polygon Vertices (N-by-3, z must be 0), Metal 
r = shape.Rectangle(Length=0.05, Width=0.03);
c = shape.Circle(Radius=0.02, Center=[0.04, 0]);
p = shape.Polygon(Vertices=[0 0 0; 0.03 0 0; 0.015 0.04 0]);

All shapes default to Metal="PEC". Set Metal="Copper" for realistic conductor loss.

Available metals: PEC, Copper, Aluminium, Gold, Silver, Zinc, Tungsten, Lead, Iron, Steel, Brass.

3D Shape Primitives

Shape Key Properties Notes
shape.Box Length, Width, Height, Center Closed box (6 faces)
shape.OpenBox Length, Width, Height, Center Box with one face removed
shape.Cylinder Radius, Height, Center, Cap Cap=[1 1] = both ends closed
shape.OpenCylinder Radius, Height, Center Open-ended cylinder
shape.Sphere Radius, Center Full sphere
shape.Custom3D Vertices (from triangulation) Arbitrary 3D mesh

3D shapes have both Metal and Dielectric properties:

wg = shape.Box(Length=0.023, Width=0.010, Height=0.030, Metal="PEC");
sub = shape.Box(Length=0.06, Width=0.06, Height=1.6e-3, Dielectric="FR4");

Boolean Operations

combined = shape1 + shape2;        % union (or add(shape1, shape2))
slotted = ground - slot;           % subtraction (or subtract(ground, slot))
overlap = shape1 & shape2;         % intersection (or intersect(shape1, shape2))

Use RetainShape=true in add/subtract to preserve internal boundaries for correct meshing at junctions.

createHole (For Slots in 2D Shapes)

For cutting holes or slots in 2D shapes, use createHole instead of subtraction. Subtraction (-) on 2D shape.* objects can produce geometry that fails to mesh:

ground = shape.Rectangle(Length=0.1, Width=0.1);
slot = shape.Rectangle(Length=0.05, Width=0.003);
slottedGround = createHole(ground, slot);    % use this, not ground - slot

For overlapping holes (e.g., a cross-shaped slot), union the hole shapes first, then cut once:

hSlot = shape.Rectangle(Length=0.05, Width=0.003);
vSlot = shape.Rectangle(Length=0.003, Width=0.05);
crossSlot = hSlot + vSlot;                    % union first
slottedGround = createHole(ground, crossSlot); % single cut

Alternative: Direct Polygon Definition

When boolean operations (createHole, -) fail or produce meshing issues, define the final shape directly as a shape.Polygon with the target outline vertices. This avoids boolean operations entirely and is often cleaner for simple truncations, chamfers, or notches.

% Instead of: rect - triangle (boolean subtraction)
% Define the truncated rectangle directly as a polygon:
halfL = patchL/2;
cornerClip = 0.008;

% Two opposite corners truncated (e.g., for circular polarization)
verts = [
    -halfL, -halfL, 0;
     halfL-cornerClip, -halfL, 0;
     halfL, -halfL+cornerClip, 0;
     halfL, halfL, 0;
    -halfL+cornerClip, halfL, 0;
    -halfL, halfL-cornerClip, 0];

truncatedPatch = shape.Polygon(Vertices=verts);

This approach is preferred when the final outline is simple to describe — fewer operations, no boolean failure modes, and explicit geometry intent.

Transforms

translate(shape, [dx, dy, dz]);
rotate(shape, angleDeg, [x1 y1 z1], [x2 y2 z2]);
rotateX(shape, angleDeg);  rotateY(shape, angleDeg);  rotateZ(shape, angleDeg);
scale(shape, factor);

Shapes are handle objects -- transforms modify the original. Use copy(shape) to preserve the original before transforming.

Vertical rectangles (walls, pins): Always rotate at the origin first, then translate. Rotating a translated shape around a point causes the large dimension to "swing" into an unexpected axis.

% CORRECT: rotate at origin, then translate
wall = shape.Rectangle(Length=wallHeight, Width=wallSpan);
rotate(wall, 90, [0, 0, 0], [0, 1, 0]);  % tip into YZ plane
translate(wall, [x, y, wallHeight/2]);     % z spans 0 to wallHeight

% ERROR-PRONE: translate first, rotate around a point
wall = shape.Rectangle(Length=wallSpan, Width=wallHeight);
translate(wall, [x, y, wallHeight/2]);
rotate(wall, 90, [x, y, wallHeight/2], [x, y+1, wallHeight/2]);  % wallSpan swings into Z

Extrusion: 2D to 3D

extrudeLinear

Extrudes a 2D shape along the z-axis. The 2D shape must be in the XY plane.

rect = shape.Rectangle(Length=0.023, Width=0.010);
box = extrudeLinear(rect, 0.030);    % height = 0.030 m

% Tapered extrusion (horn flare)
rect = shape.Rectangle(Length=0.023, Width=0.010);
horn = extrudeLinear(rect, 0.050, Scale=[2.5 2.0], NumSegments=1, Caps=false);
Argument Default Description
height -- Extrusion height along z (m)
Scale 1 [sx sy] scale factor at the far end (creates taper)
NumSegments 1 Mesh segments along extrusion
Caps false Close both ends
Direction [0 0 1] Extrusion direction
Twist 0 Twist angle (degrees)

Critical: The 2D shape must be in the XY plane. Extrude first, then rotate into position.

extrudeRotate

Revolves a 2D shape around the z-axis. Creates bodies of revolution.

profile = shape.Polygon(Vertices=[0.005 0 0; 0.01 0 0; 0.02 0.05 0; 0.015 0.05 0]);
hornRev = extrudeRotate(profile, 360, NumSegments=16);
Argument Default Description
angle -- Revolution angle (degrees, 360 = full)
NumSegments 3 Segments around the revolution
Caps false Close the ends
Pitch 0 Z-advance per revolution (helical)

Modifying 3D Structures

removeFaces

Opens a face on a closed 3D shape (e.g., waveguide aperture). Face numbering varies across shapes and MATLAB versions -- never hardcode face indices. To determine the correct face:

  1. Run removeFaces(sh) with no face index via MATLAB evaluation -- this opens an interactive GUI displaying all face numbers. Identify the correct face from the GUI output. Do not include this exploratory call in the final code.
  2. Use the resolved face number directly: removeFaces(sh, faceIdx).

imprintShape

Cuts a 2D shape outline into a 3D surface for clean feed contact:

imprintCirc = shape.Circle(Radius=0.005);
translate(imprintCirc, [feedX 0 0]);
wgWithImprint = imprintShape(wg, imprintCirc);

Feed Configuration

Delta-Gap Feed Model

Antenna Toolbox uses a delta-gap feed model. The feed edge must be at a geometric discontinuity where current is forced through the edge, not around it:

Feed Location Why It Works
Dipole gap Feed edge bridges the physical gap between two arms
Slot edge Feed edge is at metal/air boundary
Shape junction (shape1 + shape2) Boolean union creates shared edges
Probe-to-wall junction (FeedShape) Probe creates new edges perpendicular to wall
Circular gap (large NumEdges) Multiple RWG edges ring the circumference

A feed in the middle of a continuous flat plate gives ~0 ohm impedance. Always place feeds at geometric boundaries.

createFeed Syntax

FeedLocation is read-only. You must use createFeed() to define feeds.

ant = customAntenna(Shape=antShape);
createFeed(ant, [x y z], numEdges);
createFeed(ant, [x y z], numEdges, FeedShape=probeShape);  % for 3D structures
Argument Description
[x y z] Feed point coordinates (N-by-3 for multi-feed). Must be on the metal surface.
numEdges Number of mesh edges per feed. Must be 1 or >= 3.
FeedShape Optional. A 2D shape.* object defining a physical feed probe.

Choosing the Right Feed Approach

Antenna Type Feed Approach Example
2D planar (slot, dipole, patch at z=0) Bare createFeed(ant, loc, 1) Feed at slot edge or shape junction
Probe-fed patch on substrate (ground + raised patch) Imprint on ground + FeedShape=probeRect See "Probe-Fed Patch" below
3D waveguide (horn, slotted WG) FeedShape=probeRect -- physical probe Thin rectangle rotated into waveguide
Body of revolution (biconical, conical) Bare createFeed(ant, loc, N) with large NumEdges NumEdges=20 for circular feed gap

Probe-fed patch warning: For antennas where the feed bridges two parallel planes (ground to raised patch through a substrate), bare createFeed(ant, loc, 1) produces a feed edge as wide as the local mesh element. This gives unrealistically low impedance (typically 5-15 ohm instead of 50 ohm). Always use the imprint + FeedShape combination for these structures.

3D Waveguide Feeds (FeedShape)

Standard probe pattern for waveguide-based structures:

probeH = narrowWall * 0.65;    % 50-70% of narrow wall height
probeW = 5.2e-5;               % very thin (0.052 mm)
feedrect = shape.Rectangle(Length=probeH, Width=probeW);
feedX = -wgLength/2 + lambda/4;     % lambda/4 from back wall
wallZ = -narrowWall/2;
translate(feedrect, [feedX, 0, wallZ + probeH/2]);
rotate(feedrect, 90, [feedX, 0, wallZ + probeH/2], [feedX, 1, wallZ + probeH/2]);
createFeed(ant, [feedX, 0, wallZ], 1, FeedShape=feedrect);

Feed Width Control (Imprint Technique)

For probe-fed patches on substrate, use the imprint technique to control feed edge width. Without it, the feed edge width is determined by the mesh and gives unrealistically low impedance.

  1. Create a rectangle with Length = feedWidth/sqrt(2) and Width = feedWidth/sqrt(2).
  2. Rotate 45 deg with rotateZ(imprintRect, 45).
  3. Translate to feed location.
  4. imprintShape(groundPlane, imprintRect) to imprint the feed edge on the ground.
  5. Combine the imprinted ground with other metal shapes.
  6. Call createFeed(ant, loc, 1, FeedShape=probeRect) with a probe spanning ground to patch.

Probe-Fed Patch on Substrate (Complete Pattern)

% Ground with imprint at feed point
ground = shape.Rectangle(Length=gndL, Width=gndW);
feedWidth = 1.3e-3;  % SMA pin diameter (1.3 mm)
imprintRect = shape.Rectangle(Length=feedWidth/sqrt(2), Width=feedWidth/sqrt(2));
rotateZ(imprintRect, 45);
translate(imprintRect, [feedOffset, 0, 0]);
groundImprinted = imprintShape(ground, imprintRect);

% Patch raised to substrate height
patch = shape.Rectangle(Length=patchL, Width=patchW);
translate(patch, [0, 0, subH]);
metalShape = groundImprinted + patch;

% Substrate + air bounding box
substrate = shape.Box(Length=gndL, Width=gndW, Height=subH, ...
    Center=[0, 0, subH/2], Dielectric="FR4");
bbox = shape.Box(Length=0.2, Width=0.2, Height=0.1, ...
    Center=[0, 0, 0.05], Dielectric="Air", Transparency=0.1);
antShape = addSubstrate(metalShape, substrate + bbox);
ant = customAntenna(Shape=antShape);

% FeedShape: thin vertical probe from ground to patch
feedProbe = shape.Rectangle(Length=feedWidth, Width=subH);
translate(feedProbe, [feedOffset, 0, subH/2]);
rotate(feedProbe, 90, [feedOffset, 0, subH/2], [feedOffset+1, 0, subH/2]);
createFeed(ant, [feedOffset, 0, 0], 1, FeedShape=feedProbe);

Feed offset controls impedance: Moving the feed further from center increases the real part. Typical range: 15-35% of patch length for 20-120 ohm.

Imprint + FeedShape conflict: Do not place the imprint diamond too close to shape edges or vertices -- this can cause geometry errors. Keep a margin of at least 2x the imprint size from any edge.

Circular Feed (extrude technique)

Use extrude to grow a circular cross-section out of a surface, creating shared edges at the junction:

feed_circ = shape.Circle(Radius=radius, NumPoints=20);
translate(feed_circ, feed_loc);
sh = extrude(groundPlane, feed_circ, Height=height);
createFeed(ant, feed_loc, 20);   % numEdges matches NumPoints

Strip Feed

After imprinting the feed edge, create a rectangle with strip dimensions perpendicular to the surface. The bottom edge must touch (not penetrate) the surface. Use show() to verify contact.

Multi-Feed Excitation (R2026a+)

createFeed(ant, [x1 y1 z1; x2 y2 z2], [1, 1]);
ant.FeedVoltage = [1, 1];     % amplitude per feed
ant.FeedPhase = [0, 90];      % phase per feed (degrees)

For detailed feed examples (dipole, cylindrical monopole, strip, biconical), see references/Feed.md.

Dielectric Support (addSubstrate)

gnd = shape.Rectangle(Length=0.06, Width=0.06);
patch = shape.Rectangle(Length=0.03, Width=0.03);
translate(patch, [0 0 subH]);
metalShape = gnd + patch;

substrate = shape.Box(Length=0.06, Width=0.06, Height=subH, ...
    Center=[0 0 subH/2], Dielectric="FR4");
bbox = shape.Box(Length=0.2, Width=0.2, Height=0.1, ...
    Center=[0 0 0.05], Dielectric="Air", Transparency=0.1);
subShape = substrate + bbox;

antShape = addSubstrate(metalShape, subShape);

The air bounding box is required. Make it several wavelengths larger than the antenna. It must extend slightly below the ground plane (e.g., 5 mm) to fully enclose the antenna volume.

Meshing

Always mesh explicitly before analyzing custom antennas.

c = physconst("LightSpeed");
lambda = c / freq;
mesh(ant, MaxEdgeLength=lambda/6, MinEdgeLength=lambda/20);
mem = memoryEstimate(ant, freq);
fprintf("Memory estimate: %s\n", mem);

Analysis

freq = 10e9;
freqRange = linspace(freq*0.8, freq*1.2, 31);

Z = impedance(ant, freq);
fprintf("Z = %.2f + j%.2f ohm\n", real(Z), imag(Z));

hasSubstrate = isprop(ant, "Substrate") && ~isempty(ant.Substrate);
if hasSubstrate
    try
        s = sparameters(ant, freqRange, SweepOption="interp");
    catch
        s = sparameters(ant, freqRange);
    end
else
    s = sparameters(ant, freqRange);
end
figure; rfplot(s);
figure; pattern(ant, freq);
figure; current(ant, freq);

Feed coupling diagnostic: If impedance seems unrealistically low, use current(ant, freq, Scale="log") to verify the feed is physically coupling. Log-scale current reveals whether current flows into the antenna structure even when the impedance number is unreliable due to feed/mesh mismatch. If current IS flowing on the radiating elements, the antenna is working -- the impedance accuracy can be improved separately with the imprint technique.

STL/CAD Import via customAntennaStl

ant = customAntennaStl;
ant.FileName = "horn.stl";
ant.Units = "mm";
createFeed(ant, [0 0 0], 1);
figure; show(ant);
mesh(ant, MaxEdgeLength=lambda/6);

Supported formats: .stl, .step, .iges. Set UseFileAsMesh = true if the STL mesh is already fine enough.

Topology Templates

For complete code templates (horn, conical horn, patch on substrate, slot antenna, STL import), see references/topologies.md.

MATLAB Coding Standards

  • Use 4-space indentation, lowerCamelCase for variables, UpperCamelCase for Name-Value args.
  • Use "double quotes" for strings.
  • Do not add titles to Antenna Toolbox plots (show, pattern, rfplot, impedance, etc.).
  • Do add titles to manual plot() figures.
  • Use fprintf for formatted numerical output.
  • Use tiledlayout/nexttile for multi-panel figures (never subplot).

Must-Follow Rules

  • All dimensions in meters -- shape properties are in meters, not mm or cm.
  • All frequencies in Hz -- impedance, pattern, design expect Hz, not GHz.
  • Use show() to verify geometry before EM analysis -- catches modeling errors early.
  • Always define a feed -- customAntenna without createFeed cannot be analyzed.
  • Use physconst('LightSpeed') -- never hardcode 3e8.
  • Check mesh quality -- use mesh(ant, MaxEdgeLength=lambda/10) before trusting results.

Common Mistakes

% WRONG -- dimensions in mm (30 m x 20 m!)
rect = shape.Rectangle(Length=30, Width=20);
% CORRECT
rect = shape.Rectangle(Length=0.03, Width=0.02);

% WRONG -- frequency in GHz (2.4 Hz!)
impedance(ant, 2.4);
% CORRECT
impedance(ant, 2.4e9);

% WRONG -- no feed defined
ant = customAntenna(Shape=myShape);
impedance(ant, 1e9);  % Error
% CORRECT
ant = customAntenna(Shape=myShape);
createFeed(ant, [0 0 0], 1);
impedance(ant, 1e9);

% WRONG -- internal boundary lost in CSG union
combined = add(waveguide, flare);
% CORRECT -- RetainShape preserves internal boundary
combined = add(waveguide, flare, RetainShape=1);

Guidelines

  • Do not over-explain antenna theory. The user is a professional.
  • Use shape.* classes with customAntenna, never antenna.* classes.
  • Shapes are handle objects -- transforms modify in-place. Use copy() if you need the original.
  • extrudeLinear requires XY-plane shapes -- extrude first, then rotate into position.
  • FeedLocation is read-only -- always use createFeed().
  • Feed must be at a geometric discontinuity -- place feeds at gaps, slot edges, shape junctions, or probe contact points.
  • Match the feed method to the topology -- bare createFeed for 2D planar, FeedShape for waveguide, large NumEdges for body-of-revolution.
  • Use FeedShape for waveguide feeds -- probe height controls coupling strength (50-70% of narrow wall). Section must be at least 3 lambda; use design(waveguide, freq) for dimensions.
  • Always mesh explicitly before analysis. Use imprintShape when a feed probe meets a 3D surface.
  • addSubstrate requires an air bounding box -- extend it below the ground plane.
  • removeFaces for openings -- resolve face index interactively first, never hardcode.
  • Polygon vertices must have z=0 -- strictly 2D. Use extrusion for 3D.
  • Recommend show() after construction to verify geometry before expensive analysis.
  • Check memoryEstimate before analyzing electrically large structures.
  • Use removeSlivers if boolean operations produce missing geometry artifacts.

Copyright 2026 The MathWorks, Inc.